空间载荷机柜热控设计的仿真研究

空间站主动热控系统的作用是提供和保持航天员、仪器设备和结构部件所要求的温度、湿度和风速等热环境。本文以空间载荷机柜为热控系统的基本单元，建立了以单相流体循环回路为基础、采用液冷结合风冷的冷却方式的载荷机柜数学模型；介绍了模糊增量控制算法的工作原理；提出了采用模糊增量控制算法，以液冷支路进出口温差和风冷支路冷却量占总冷却量的比值为控制目标的反馈控制策略。同时文章采用数值模拟方法研究了控制系统的动态响应效果。仿真结果显示，模糊增量控制算法具有响应迅速、超调量小、无静态误差的特点，控制策略满足有效性、稳定性和高精确度的要求。     

Fault mode probability factor based fault-tolerant control for dissimilar redundant actuation system

This paper presents a Fault Mode Probability Factor (FMPF) based Fault-Tolerant Control (FTC) strategy for multiple faults of Dissimilar Redundant Actuation System (DRAS) composed of Hydraulic Actuator (HA) and Electro-Hydrostatic Actuator (EHA). The long-term service and severe working conditions can result in multiple gradual faults which can ultimately degrade the system performance, resulting in the system model drift into the fault state characterized with parameter uncertainty. The paper proposes to address this problem by using the historical statistics of the multiple gradual faults and the proposed FMPF to amend the system model with parameter uncertainty. To balance the system model precision and computation time, a Moving Window (MW) method is used to determine the applied historical statistics. The FMPF based FTC strategy is developed for the amended system model where the system estimation and Linear Quadratic Regulator (LQR) are updated at the end of system sampling period. The simulations of DRAS system subjected to multiple faults have been performed and the results indicate the effectiveness of the proposed approach.     

Implementation of tactical maneuvers with maneuver libraries

This study creates and combines the general maneuver libraries for fixed-wing aircraft to implement tactical maneuvers. First, the generalized maneuver libraries are established by analyzing the characteristics of tactical maneuvers required in battlefields. The 7th order polynomial is applied to both the creation of the maneuver libraries and the generation of the trajectories or flight paths for modal inputs. To track the desired trajectory, we design the Attitude Command Attitude Hold (ACAH) system and the Rate Command Rate Hold (RCRH) system using Model Following Controller (MFC). Moreover, the Line-of-Sight (LOS) guidance law is designed. In particular, the CONDUIT® is employed to optimize the gains so that the control systems meet the aircraft Handling Qualities (HQ) criteria. Finally, flight simulations are performed for the longitudinal loop, immelmann-turn, and climb-slalom-descent maneuvers to verify that tactical aggressive maneuvers are realizable via the combination of maneuver libraries. This study can contribute to the development of flight techniques for aircraft tactical maneuvers and to the revision of air force operational manuals.     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

轨控大干扰下的系统角动量管理

摘要： 针对利用角动量交换装置系统实现轨控期间姿态维持的情况，研究当轨控推力器存在大力矩扰动时系统角动量管理方法.结合对地运行航天器轨道运动特性，分析轨控干扰力矩的积累角动量变化规律；考虑角动量管理装置系统的角动量存贮容量，基于角动量积累规律提出了一种结合偏置角动量建立与对称分布轨控位置选择的系统角动量管理方法，实现了对称轨控位置积累角动量互相抵消的自平衡效果，极大程度地提高轨控效率且避免系统角动量饱和现象.所提出的方法适用于喷气欠驱动控制系统，方法的有效性通过了数学仿真验证及在轨型号应用.     

An improved numerical method for constructing Halo/Lissajous orbits in a full solar system model

An improved numerical method that can construct Halo/Lissajous orbits in the vicinity of collinear libration points in a full solar system model is investigated. A full solar system gravitational model in the geocentric rotating coordinate system with a clear presentation of the angular velocity relative to the inertial coordinate system is proposed. An alternative way to determine patch points in the multiple shooting method is provided based on a dynamical analysis with Poincare′sections. By employing the new patch points and sequential quadratic programming, Halo orbits for L_1, L_2, and L_3 points as well as Lissajous orbits for L_1 and L_2 points in the EarthMoon system are generated with the proposed full solar system gravitational model to verify the effectiveness of the proposed method.     

不同密度弹丸对水冰的超高速撞击成坑实验

为了研究冰冻天体表面撞击坑的形成与演化，开展了水冰的超高速撞击成坑实验。使用二级轻气炮发射1.0 mm直径的球形弹丸，以3 km/s、5 km/s和7 km/s速度对圆柱状冰块进行撞击。弹丸材料包括聚碳酸酯和不锈钢两种，冰块温度为253 K。实验观察到了不同弹丸和不同速度条件下，冰块中撞击坑的形貌特征。对撞击坑直径、深度和剖面形状进行了测量，并与文献中铝弹丸对水冰的撞击坑进行了比较分析。获得了水冰撞击坑特征随撞击参数的变化规律，结果表明：撞击坑直径和深度的主导机制不同，坑深主要由弹丸侵彻作用形成，而坑径主要由冰块的剥落所致；坑深比坑径具有更强的对于弹丸密度的依赖性，高密度弹丸撞击坑直径具有比低密度弹丸更强的对于撞击速度的依赖性；撞击坑体积与撞击能量成正比，高密度弹丸形成的撞击坑直径表现出“能量缩比”行为，而低密度弹丸形成的撞击坑直径表现出“动量缩比”行为。     

酚醛树脂基纳米多孔材料的制备及结构调控

酚醛树脂基纳米多孔材料（Phenolic Resin-based Nanoporous Materials，PNM）是满足新一代航天飞行器轻质、高效隔热需求的新型热防护材料，传统制备方法中需使用超临界干燥技术，制备周期长、成本高。本研究通过两步法，即先合成线性酚醛树脂，再进行溶胶-凝胶的方法，实现了常压干燥PNM的制备。系统研究了固化剂含量、固化温度和固化时间对材料结构的影响和调控作用，分析了影响材料收缩率和热稳定性的因素。结果表明，PNM的微观纳米结构的变化会影响材料干燥后的收缩率，制备大颗粒、大孔径的微观结构更有利于降低材料的收缩率。而PNM的热稳定性主要受交联反应过程形成的化学结构的影响，通过优化固化剂的含量可提高PNM的热稳定性。当固化剂含量为10%，固化温度提高至150℃，固化时间延长至48 h的条件下，获得的PNM有最高的热稳定性（900℃下的残碳率为54.2%）、最发达的孔结构（比表面积为264.0 m²/g、孔容为2.67 cm³/g、平均孔径为40.0 nm）和最小的收缩率（0%）。此PNM制备方法简单、性能优异，在未来航天飞行器上有广阔的应用前景。     

电铸镍Wolter I型光学系统制造技术发展综述

摘要： 为满足未来脉冲星导航和空间天文观测任务对X射线望远镜的载荷需求，Wolter I光学系统的研制正逐渐成为新的研究热点，电铸镍方案是当前国内外X射线光学系统镜筒制造的主要技术方案.文章对电铸镍X射线光学系统制造工艺、国内外研制现状、未来应用需求进行了介绍和整理，梳理了电铸镍X射线光学系统研制遇到的关键技术和难点，提出了后续研究发展建议，以促进中国在 X射线脉冲星自主导航、空间探测领域的快速发展.     

反推装置对翼身融合分布式推进系统气动性能影响数值模拟

为了研究新型反推装置对翼身融合分布式推进系统气动性能的影响,将机身简化为二维模型,利用数值模拟的手段来研究攻角、反推开度,以及风扇打开或关闭对飞行参数的影响,为翼身融合分布式推进系统的反推装置设计提供初步的意见和建议。结果显示:反推闭合和风扇打开之后该机型的升力系数和俯仰力矩系数都会有较大增加;随着反推开度的增加,升力系数和俯仰力矩系数也随之增加;来流攻角对翼身融合分布式推进系统的气动性能也有较大影响。